Rinsing Baby Bottles After Sterilising: A Simple Habit to Cut Plastic Shedding, Done Safely
Why researchers suggest rinsing sterilised plastic bottles with cooled boiled water, how to do it without adding germs, and what the evidence does and…
PBy Pramod RimalPublished Updated 11 min read

On this page
- What the research found
- What we don't know
- Step by step: the rinse habit
- Why tap water is not OK for this rinse
- How the rinse fits with each country's formula method
- Other habits that lower plastic shedding
- Sterilising methods compared
- How long do you need to sterilise?
- Breast pumps and expressed milk
- Cleaning bottles properly before you sterilise
- Setting up a simple bottle station
- Teats, valves and other plastic parts
- Day care, travel and nights out
- Plastic, glass or silicone bottles: a quick comparison
- Age stages
- A printable checklist
- Keeping it in proportion
- Common mistakes to avoid
- Is it worth the effort?
- FAQ
- Sources
Short answer: plastic baby bottles shed tiny bits of plastic (microplastics) when they get hot, including during sterilising. A 2020 study from Trinity College Dublin suggested a simple extra step: after sterilising, let the bottle cool, then rinse it at least three times with room-temperature water that has been boiled. The idea is to wash away particles loosened by the heat before milk goes in. It's an easy habit, but do it safely: only ever rinse with boiled and cooled water, never plain tap water, so you don't add germs back. You may see claims that it cuts shedding by a set percentage; the study recommends the step but we couldn't confirm an exact figure, and health agencies say there's no clear proof yet that microplastics harm health.
Key points
- Why: heat makes polypropylene bottles shed more particles. Rinsing after sterilising may wash some away.
- How: sterilise, cool, then rinse at least 3 times with boiled water that has cooled to room temperature.
- Never rinse sterilised bottles with plain tap water. It can put germs back.
- Don't skip sterilising. Germs are a proven risk for young babies; microplastic harm is not yet proven.
- Other easy habits: boil water in a glass or metal kettle, mix hot formula in a glass or steel jug, don't microwave milk in plastic.
What the research found
In 2020, researchers at Trinity College Dublin published a study in Nature Food on polypropylene baby bottles. Polypropylene (PP, number 5 in the recycling triangle) is the plastic most baby bottles are made from.
They followed World Health Organization steps for sterilising and preparing formula, and counted the plastic particles released. According to the university's summary:
- At 25°C (room temperature), bottles released about 0.6 million particles per litre.
- At 70°C, the temperature used to make up formula in some countries, release went up to 16.2 million per litre.
- At 95°C, close to boiling, it went as high as 55 million per litre.
Heat made a big difference. The researchers also found that sterilising itself, which uses very hot water or steam, released particles.
They suggested some changes to everyday steps. One of them was to rinse sterilised bottles with room-temperature sterilised (boiled) water at least three times before use. Other steps included boiling water in a non-plastic kettle, mixing formula in a non-plastic container, and not shaking hard.
What we don't know
It's important to be honest about the limits:
- The numbers are from a lab. They count particles in liquid, not what reaches a baby's body.
- Health effects aren't proven. Food Standards Australia New Zealand (FSANZ) says very little of the plastic we swallow seems to be absorbed and that it's unlikely to cause immediate harm, though more research is needed. The World Health Organization also said in 2019 that there wasn't enough evidence to show a health risk from microplastics in drinking water.
- Exact savings are unclear. You may see headlines claiming the rinse cuts shedding by a set amount. We couldn't confirm a specific percentage from the study's public summary, so we don't repeat one here.
So rinsing is a low-cost, low-effort way to be careful. It isn't something you must do, and it should never replace proper sterilising or safe formula preparation.
Step by step: the rinse habit
- Clean the bottle. Wash bottles, teats and caps in hot soapy water with a bottle brush, then rinse. The NHS notes that a dishwasher cleans bottles but doesn't sterilise them.
- Sterilise as usual. Use boiling, steam or a cold-water sterilising solution, following your health service and the steriliser's instructions.
- Boil fresh water for rinsing, ideally in a glass or stainless steel kettle or a pot, and let it cool to room temperature in a clean, covered container.
- Wash your hands before handling sterilised items.
- Let the bottle cool after sterilising.
- Rinse at least three times: pour in some cooled boiled water, swirl, pour out. Repeat.
- Use the bottle straight away, or put the lid and teat back on and store it covered.
If you use a cold-water sterilising solution, the NHS says you can shake off the extra solution or rinse with cooled boiled water rather than tap water. This rinse step fits right in.
Why tap water is not OK for this rinse
The whole point of sterilising is to kill germs that could make a young baby sick. Tap water in Australia, the UK, the US and Canada is safe for adults to drink, but it isn't sterile. Rinsing a just-sterilised bottle with tap water can put germs back on it.
Always use water you have boiled and cooled. Keep it covered so dust and germs don't get in, and make fresh each day.
How the rinse fits with each country's formula method
| Country | Formula method | How to add the rinse | Lower-plastic tip |
|---|---|---|---|
| Australia | Boil water, cool to lukewarm, then add powder (Pregnancy, Birth and Baby) | Rinse the cooled, sterilised bottle with cooled boiled water, then add your lukewarm water and powder | Water is already cool when it meets the bottle |
| United Kingdom | Mix powder with water at 70°C or more (NHS) | Rinse the sterilised bottle with cooled boiled water | Mix the hot formula in a sterilised glass or steel jug, cool it, then pour into the bottle |
| United States | Safe water; boil for babies under 2 months, preterm or with weak immunity (CDC) | Rinse with cooled boiled water after sterilising | Mix in a non-plastic container if using hot water |
| Canada | Follow Health Canada and your formula label | Rinse with cooled boiled water after sterilising | Same as above |
Keep following your country's formula method. The rinse is an extra step, not a change to the safety rules.
Other habits that lower plastic shedding
- Boil water in a glass or stainless steel kettle, or a pot, instead of a plastic kettle.
- Don't microwave milk in plastic. Warm bottles in a bowl of warm water. Microwaves also make hot spots that can burn.
- Swirl, don't shake hard. The study found shaking released more particles.
- Don't use ultrasonic cleaners on plastic bottles, as the researchers advised against it.
- Replace old bottles that look cloudy, scratched or cracked.
- Consider glass or silicone bottles if you'd like less plastic contact. Glass needs care as it can break.
Sterilising methods compared
| Method | How it works | Heat on the plastic | Good to know |
|---|---|---|---|
| Boiling | Items covered in boiling water, usually for about 10 minutes (NHS) | High | Teats wear faster; check them often |
| Electric steam steriliser | Steam heats items | High | Quick and easy; follow the maker's steps |
| Microwave steam bag or box | Steam in the microwave | High | Check the bottle is microwave-safe; never microwave milk |
| Cold-water solution | Items soaked in a sterilising solution for at least 30 minutes; change it every 24 hours (NHS) | None | No heat on the plastic; shake off or rinse with cooled boiled water |
A cold-water sterilising solution avoids heating the plastic altogether. Some parents choose it for that reason. All methods work for killing germs when done properly.
How long do you need to sterilise?
Health services in Australia and the UK suggest sterilising bottles, teats and feeding equipment for the first 12 months. In the US, the CDC suggests sanitising feeding items at least once a day, especially for babies under 2 months, babies born early, or babies with weak immune systems. Ask your child health nurse, health visitor or doctor what's right for your baby. Once you stop sterilising, the rinse step is no longer needed.
Breast pumps and expressed milk
Many breast pump parts and storage bottles are also plastic. The same ideas apply: clean them well, sterilise as advised, let them cool, and rinse with cooled boiled water if you like. Store and warm breast milk gently, in glass where you can, and never microwave it.
Cleaning bottles properly before you sterilise
Sterilising only works on clean equipment. Milk left inside a bottle can protect germs from the heat or solution. Before you sterilise:
- Rinse straight after the feed in cold water, so milk doesn't dry on.
- Take everything apart: bottle, teat, ring, cap and any valves or vents.
- Wash in hot soapy water using a clean bottle brush and a small teat brush.
- Squeeze water through the teat hole to clear any milk.
- Rinse off the soap in clean water.
- Check for damage: cracks, cloudiness, sticky or torn teats. Replace them.
Use a brush kept only for baby bottles, and let it dry between uses. A soft brush also scratches plastic less, and scratched plastic may shed more over time.
Setting up a simple bottle station
A tidy bottle station makes the rinse habit easy, even at night:
- A clean, covered jug or bottle of boiled water that's cooling or cooled, labelled with the day.
- Your steriliser, or a clean pot for boiling.
- A clean drying rack, used only for bottles.
- Sterilised tongs to lift items, so your hands don't touch the inside.
- Formula powder and a scoop, kept dry and closed.
- A glass or steel jug for mixing formula, if you use hot water.
Wipe the bench with hot soapy water before you start, and keep the station away from raw meat and the sink where dirty dishes go.
Teats, valves and other plastic parts
Teats are usually silicone, and caps, rings and anti-colic valves are often plastic. The Trinity College study looked at the bottle body, but the same idea of cooling and rinsing applies to all parts that touch milk. Teats also wear out with heat. Check them before every feed and replace them when they're sticky, cracked, torn, or the hole has grown. A damaged teat can also be a choking risk.
Day care, travel and nights out
- Day care: send clean, sterilised and rinsed bottles with caps on. Ask how the centre stores and prepares feeds.
- Travel: cold-water sterilising tablets and a container are light to pack. Carry boiled water that has cooled in a clean flask for rinsing.
- Grandparents and babysitters: show them the steps, including "boiled water only, never tap water, for rinsing".
- Ready-to-feed formula is handy away from home and doesn't need hot water.
Plastic, glass or silicone bottles: a quick comparison
| Bottle | Sheds plastic when hot? | Breaks? | Rinse needed for microplastics? |
|---|---|---|---|
| Polypropylene plastic | Yes, more when hot | No | Recommended by the study team |
| Glass | No | Can break; use a sleeve | Not for the bottle itself |
| Silicone | Less studied | No | Optional |
| Stainless steel | No | Can dent | Not for the bottle itself |
Age stages
Newborn to 3 months
This is when babies are most at risk from germs and when you'll sterilise most often. Follow sterilising steps carefully. Add the cooled boiled water rinse if you'd like to lower plastic shedding.
3 to 12 months
Keep sterilising as your health service advises. Your baby may drink larger feeds, so you may switch to bigger bottles. Check teats as your baby's sucking gets stronger.
12 months and older
Most children move to cups around 12 months. Once you stop sterilising, the rinse isn't needed. Wash cups in hot soapy water, and use cool drinks in plastic cups.
A printable checklist
- Wash hands and wipe the bench.
- Rinse, take apart and wash bottles in hot soapy water.
- Sterilise as your health service says.
- Boil fresh water in a glass or metal kettle and let some cool, covered.
- Let sterilised bottles cool.
- Rinse 3 times with the cooled boiled water.
- Make formula your country's way; mix hot formula in a glass or steel jug.
- Cool, then pour into the bottle. Test on your wrist.
- Throw away leftover milk after the feed.
Keeping it in proportion
Babies, like all of us, meet microplastics from many places: food packaging, dust, water and air. Bottles are one source you can change easily, which is why this habit is popular. But it's one small part of a bigger picture, and science is still working out what it means for health. If the extra steps cause stress, focus on the basics that are known to protect your baby: clean equipment, sterilising, safe water, and making each feed fresh.
Common mistakes to avoid
- Rinsing with tap water after sterilising.
- Skipping sterilising to avoid heat. Germs are the bigger, proven risk.
- Leaving rinse water uncovered on the bench for hours.
- Using the same rinse water for days. Boil fresh water each day.
- Touching the inside of bottles or teats with unwashed hands.
- Believing any exact percentage claim without seeing where it came from.
Is it worth the effort?
For most families, the rinse adds about a minute. If you're already boiling water for formula, you can set some aside to cool for rinsing. It's a reasonable step for parents who want to lower plastic exposure while science catches up. If it makes feeding too hard on a busy night, skipping it once is not a safety risk. Proper cleaning, sterilising and safe formula preparation are what matter most.
FAQ
Does rinsing after sterilising undo the sterilising?
Not if you use boiled and cooled water and clean hands. Tap water would, which is why it's not recommended.
How many times should I rinse?
The Trinity College researchers suggested at least three times with room-temperature sterilised water.
Do I need to rinse glass bottles?
Glass doesn't shed plastic, so the rinse isn't needed for that reason. Plastic teats and caps are silicone or plastic, though, so some parents still rinse.
Is it true rinsing cuts microplastics by 90%?
We couldn't confirm that figure in the study's public summary. The researchers recommend rinsing, but you should treat specific percentages with caution unless they come with a clear source.
Is cold-water sterilising better for microplastics?
It avoids heating the plastic, so it likely releases fewer particles. It's an approved sterilising method when used correctly.
Are microplastics harmful to my baby?
There's no clear proof yet. FSANZ and the WHO say more research is needed. Lowering exposure is a careful choice, not an emergency.
Can I store rinsed bottles?
Yes. Put the teat and cap back on and store covered in a clean place, or leave them in the steriliser until needed, as your steriliser's instructions say.
Can I use bottled water for the rinse?
Bottled water isn't sterile either. Boil it and let it cool first, the same as tap water.
Should I rinse bottles that I've cleaned in the dishwasher?
A dishwasher cleans but doesn't sterilise. For young babies, sterilise afterwards as your health service suggests, then rinse with cooled boiled water if you'd like.
How long can I keep cooled boiled water for rinsing?
Make it fresh each day. Keep it in a clean, covered container. Pregnancy, Birth and Baby says sealed bottles of boiled and cooled water can be kept in the fridge for up to 24 hours, which is a good guide for rinse water too.
Is it OK to let bottles air dry after rinsing?
Yes, on a clean rack used only for bottles, away from splashes and dirty dishes. Don't dry inside them with a tea towel, as towels can carry germs.
Will the rinse change how the milk tastes?
No. You're only rinsing with plain boiled water. Shake out the last rinse before adding water or formula so the amounts stay correct.
Do I need to rinse sippy cups or straw cups?
Not usually. Most children use these after 12 months, when sterilising is no longer needed. Wash them well in hot soapy water, use a straw brush, and fill plastic cups with cool drinks rather than hot ones.
Sources
- Li D. et al. (2020) – Microplastic release from the degradation of polypropylene feeding bottles during infant formula preparation, Nature Food
- ScienceDaily (Trinity College Dublin release) – High levels of microplastics released from infant feeding bottles
- Food Standards Australia New Zealand – Microplastics in food
- World Health Organization – Microplastics in drinking-water (2019)
- NHS – Sterilising baby bottles
- NHS – How to make up baby formula
- Pregnancy, Birth and Baby – Feeding your baby with formula
- CDC – Infant formula preparation and storage
Pramod Rimal
Founder & editor
Practical, evidence-led guides for Australian families. We check claims against Australian standards and official health and safety guidance, and link our sources so you can check them too.
Visit Pramod Rimal’s website →About us and how we research →
Related guides
More Parental Tips →Microplastics in Baby Bottles: Glass vs Silicone vs Plastic, and Simple Ways to Cut Them Down
30 Oct 2026 · 11 min read
Preparing Your Toddler for a New Baby: Simple Ways to Help Them Adjust
20 Oct 2026 · 15 min read
How to Introduce Peanut, Egg, Dairy and Other Allergens to Your Baby Safely
30 Oct 2026 · 12 min read













