How to Use and Maintain Your Baby Bottle Steriliser and Dryer
Learn how to use, clean, and descale your baby bottle steriliser and dryer safely, with step-by-step care tips and AU, UK, US and Canada guidance.
PBy Pramod RimalPublished Updated 14 min read

On this page
- Key points
- What a bottle steriliser and dryer does
- Types of bottle sterilisers and dryers
- How to use a bottle steriliser and dryer, step by step
- What you can and cannot put inside
- How to clean and descale your machine
- Can you use distilled or filtered water?
- Official guidance in Australia, the UK, the US and Canada
- Common mistakes to avoid
- Safety tips around heat, steam and power
- Troubleshooting common problems
- Frequently asked questions
- Sources
Short answer: Wash every bottle part in warm soapy water before it goes into the machine. Place bottles upside down so steam gets inside and water drains out. Run the sterilise and dry cycle, then let the unit cool before you open the lid. Descale the heating plate every few weeks and clean the air filter so your machine stays safe and works well.
A bottle steriliser and dryer saves time, but it only works when you load it right and keep it clean. Milk film left on a bottle stops steam from reaching germs. Hard water scale on the heating plate slows the machine down and can trigger error lights.
Key points
- Wash first: always scrub bottles, teats (nipples) and rings with warm soapy water and a brush first.
- Measure the water: use the exact amount of water listed in your user manual.
- Load upside down: point bottle openings down so steam enters and water drips out.
- Leave gaps: do not cram items together. Steam and hot air need space to move.
- Cool before opening: hot steam can burn skin fast. Wait for the cool-down phase.
- Descale often: wipe away chalky white mineral build-up on the heating plate every 1 to 4 weeks.
- Check the filter: rinse or swap the dryer air filter when it looks dusty.
What a bottle steriliser and dryer does
Washing and sterilising are two different jobs. Washing with soap and water removes leftover milk, fat and spit. Sterilising uses high heat, steam or UV light (ultraviolet light) to kill germs that soap might miss.
Young babies have immune systems that are still growing. Milk is also a rich food for bacteria. If tiny germs stay inside a warm bottle, they can multiply fast and upset your baby's tummy.
Drying matters just as much as sterilising. Wet bottles sitting in a closed rack can grow mould or new bacteria. A built-in dryer blows warm, filtered air over the clean items so they come out bone dry and ready to store.
Do you still need to boil bottles first?
No, not once your machine is working properly. If your steriliser is new, read the manual first. Many makers ask you to run one empty cycle with plain water before the first real load. That rinses out any factory dust.
Types of bottle sterilisers and dryers
Not all machines work the same way. Knowing which type you own helps you use and clean it properly.
| Type | How it kills germs | Drying built in? | Main care job |
|---|---|---|---|
| Electric steam steriliser and dryer | Boils water into hot steam | Yes, warm air fan | Descale heating plate and clean air filter |
| Electric steam steriliser (no dryer) | Boils water into hot steam | No, air dry only | Descale heating plate and wipe lid |
| Microwave steam steriliser | Uses microwave heat to boil water | No, air dry only | Wash tray and check water level each time |
| UV-C steriliser and dryer | Shines ultraviolet light on items | Yes, gentle warm air | Wipe mirrors, clean filter, swap bulbs if needed |
If you travel or lose power, you still have simple backups. You can boil heat-safe bottles in a large pot of water on the stove. You can also use cold-water sterilising tablets in a clean lidded tub, following the pack directions.
How to use a bottle steriliser and dryer, step by step
Follow these steps for electric steam sterilisers with a dryer. Always check your own manual for exact water amounts and cycle times.
- Wash your hands. Use soap and warm water for at least 20 seconds. Dry your hands on a clean towel.
- Take every bottle apart. Separate the bottle, screw ring, teat (nipple), cap and any inner vent tubes or valves.
- Wash every piece well. Use hot, soapy water and a clean bottle brush. Use a small teat brush for the tiny tip and vent holes. Squeeze soapy water through the teat hole.
- Rinse with clean water. Rinse off all soap bubbles. Leftover soap can leave a film or taste on the teat.
- Check the heating plate. Make sure the metal plate at the bottom of the base is clean and free of old water or milk drips.
- Measure the water. Pour the exact amount of water onto the plate. Too little water can stop the cycle early. Too much water can spill over or leave items wet.
- Load the bottom rack. Stand bottles upside down over the pegs or open spaces. Place screw rings and caps loosely beside them, not stacked inside each other.
- Load the top tray. Lay teats, dummies (pacifiers) and small pump valves flat or facing down. Make sure nothing touches the lid or blocks the steam vents.
- Close the lid firmly. Check that the lid sits flat all the way around so steam stays inside.
- Pick your cycle. Most machines offer three modes: sterilise only, dry only, or auto (sterilise then dry). Pick auto for everyday use.
- Let it finish and cool. Wait until the cycle beeps or the light turns off. Wait a few extra minutes before lifting the lid.
- Open safely. Stand back and lift the lid away from your face. Trapped steam can scald you fast.
- Store clean items safely. If your machine has a clean storage mode, keep the lid shut until feed time. If you take bottles out, put them together with clean hands and store them in a clean, covered container.
Tips for UV-C sterilisers and dryers
UV machines do not use water or steam. That means you do not need to descale a heating plate. Still, UV light only kills germs on surfaces it can see.
- Shake excess water off washed bottles before loading, or use the dry-first mode.
- Place bottles upright or angled as the manual shows, so light shines inside the bottle neck.
- Never stack bowls or cups on top of each other.
- Keep the shiny metal walls inside the cabinet clean and free of water spots, because they bounce the UV light around.
What you can and cannot put inside
High heat and steam are great for germs, but they can warp or melt the wrong materials. Always check the heat symbol or care note on each item first.
| Item | Steam steriliser and dryer | UV-C steriliser and dryer | What to check |
|---|---|---|---|
| Glass baby bottles | Yes | Yes | Check for chips or cracks before heating |
| Heat-safe plastic bottles | Yes | Yes, check manual | Look for dishwasher-safe or boiling-safe marks; UV can tint some plastics |
| Silicone teats and dummies | Yes | Check manual | UV light can make some clear silicone turn cloudy or brittle over time |
| Breast pump shields and valves | Usually yes | Check manual | Check your pump guide; thin silicone duckbill valves wear faster with high heat |
| Breast pump air tubing | No, unless manual says yes | No, unless manual says yes | Air tubes normally do not touch milk and can melt or trap water inside |
| Soft plastic teethers with gel | No | No | Heat can burst gel teethers; wash with warm soapy water instead |
| Wooden spoons or bamboo plates | No | No | Steam cracks wood and ruins bamboo glue |
Watch your plastic bottles closely over time. If a plastic bottle looks cloudy, deeply scratched or cracked, replace it. Deep scratches can hide germs and are hard to scrub clean. Also check teats by pulling the tip gently before each feed. Throw away any teat that is sticky, torn, swollen or cracked.
How to clean and descale your machine
Even clean-looking tap water holds minerals like calcium and magnesium. When water boils away on the metal plate, those minerals stay behind. Over days and weeks, they form a chalky white, grey or brown crust called scale.
Scale is bad for your machine in three ways:
- It slows down heating, so steam cycles take longer or stop early.
- It can make the sensor think the plate is dry, causing error beeps.
- It can flake off and leave gritty dust on your clean bottles.
How often should you descale?
If your home has hard water, descale every 1 to 2 weeks. If your water is soft or you use filtered or distilled water, once every 3 to 4 weeks is often enough. Any time you see white spots, chalky rings or brown marks on the plate, it is time to descale.
Step-by-step descaling guide
Always check your user manual before descaling. Some makers prefer citric acid powder, while others suggest plain white vinegar. Never use harsh bleach, oven cleaner or metal scouring pads on the heating plate.
- Unplug the unit. Pull the plug out of the wall and let the machine cool down completely.
- Empty the trays. Lift out the bottle racks and lid. Wash them in warm soapy water, rinse and set aside to dry.
- Mix your descaling solution. A common mix is equal parts plain white vinegar and water (for example, half a cup of each), or 1 packet of food-grade citric acid dissolved in water as your manual states.
- Pour onto the plate. Pour just enough mix to cover the metal heating plate. Do not fill past the normal max line.
- Let it soak. Leave the mix to sit for 30 to 60 minutes. For thick crust, leave it for 1 to 2 hours. Do not turn the heating cycle on with vinegar inside unless your manual specifically tells you to, as hot vinegar fumes smell strong and can wear rubber seals.
- Wipe gently. Pour the mix down the sink. Use a soft cloth or non-scratch sponge to wipe away loosened scale.
- Rinse well. Wipe the plate with a clean damp cloth several times until there is no vinegar smell left.
- Run a rinse cycle if needed. If the smell lingers, add the normal amount of plain water, run one short steam cycle without bottles, let it cool, and wipe dry.
Cleaning the lid, racks and outside body
Wash the lid, bottle pegs and top tray in warm soapy water once a week. If your manual says they are top-rack dishwasher safe, you can wash them there instead. Wipe the outside of the base with a damp cloth, then dry it.
Never dunk the electric base, power cord or plug in water. Water inside the base can ruin the fan and heater and create an electric shock risk.
Cleaning or replacing the air filter
Most bottle dryers have a small air intake on the underside or back of the base. Behind a small clip-on cover sits a sponge filter or a pleated HEPA filter (a fine filter that traps household dust).
Check this filter every 2 to 4 weeks. If dust clogs the filter, less air reaches your bottles. Drying will take longer, and bottles may still feel damp at the end of the cycle.
- Sponge filters: gently wash in warm water, squeeze out, and let dry completely before putting back.
- Pleated paper or HEPA filters: do not wash with water unless the manual says it is washable. Tap off loose dust or swap for a fresh filter every few months.
Can you use distilled or filtered water?
Yes. Using distilled water (water boiled into steam and cooled back down) or filtered water cuts down mineral scale a lot. Your heating plate stays shiny for much longer, and you will descale far less often.
Tap water is still safe to use for steam sterilising. The boiling heat turns the water into pure steam, leaving minerals behind on the plate. Just be ready to descale more often if your tap water is hard.
Never put breastmilk, formula, soapy water or essential oils onto the heating plate. They will burn onto the metal, ruin the heater and coat your bottles in sticky fumes.
Official guidance in Australia, the UK, the US and Canada
Health authorities in all four countries agree on the main rule: washing bottles thoroughly comes first, and safe sterilising protects young babies from harmful germs. How long you need to sterilise varies slightly by country.
| Country | Official bodies | Main advice on washing and sterilising |
|---|---|---|
| Australia | Raising Children Network, Pregnancy, Birth and Baby, NHMRC | Wash bottles and teats in hot soapy water with a bottle brush first. Sterilise all bottle-feeding gear until your baby is 12 months old. |
| United Kingdom | NHS | Wash all feeding equipment in hot soapy water and rinse before sterilising. Sterilise bottles, teats and dummies until your baby is at least 12 months old. |
| United States | CDC | Clean bottles after every feed. Sanitise daily for babies under 2 months, born early, or with weak immune systems. Older healthy babies may not need daily sanitising if bottles are washed well by hand or in a hot dishwasher cycle. |
| Canada | Health Canada, Canadian Paediatric Society (Caring for Kids) | Wash bottles, teats and caps in warm soapy water with a brush. Sterilise feeding items for newborns and young babies, especially under 4 months or if born early or unwell. |
Global guidance from the World Health Organization (WHO) also stresses clean equipment when making powdered baby formula. Clean, sterilised bottles help lower the risk of serious tummy bugs in newborns.
What about plastic bottles and heat?
Parents often ask if heating plastic bottles in a steam steriliser is safe. Food Standards Australia New Zealand (FSANZ) and the US Food and Drug Administration (FDA) note that baby bottles sold in these markets no longer use Bisphenol A (BPA). Still, it is smart to follow simple habits:
- Check that every plastic bottle is marked safe for boiling or steam.
- Do not leave plastic bottles sitting in hot water longer than the cycle needs.
- Replace plastic bottles that look scratched, cloudy or worn.
- Consider glass or silicone bottles if you prefer to avoid heated plastic altogether.
Common mistakes to avoid
Most problems with bottle sterilisers come from small daily habits. Fixing these keeps your gear working and your baby safe.
- Skipping the wash step: steam cooks leftover milk onto the plastic. That film traps bacteria underneath. Always wash with soap and a brush first.
- Overfilling the racks: cramming too many bottles in blocks steam and hot air. Leave a small gap around each piece.
- Standing bottles right-side up: steam rises, and water pools inside an upright bottle. Always place bottles upside down.
- Guessing the water amount: using a random splash of water causes short cycles or messy spills. Use the measuring cup that came with the unit.
- Forgetting the air filter: a dusty filter chokes the fan. Bottles come out wet, and the motor works too hard.
- Using metal scrubbers on the plate: steel wool scratches the coating off the heating plate. Scratches make scale stick even harder next time.
- Touching clean teats with unwashed hands: your hands carry germs right back onto the sterile teat. Wash your hands or use clean tongs to lift teats out.
- Storing damp bottles in a closed box: if you skip the dry cycle, let bottles air dry on a clean rack or paper towel before putting lids on.
Safety tips around heat, steam and power
A bottle steriliser and dryer reaches boiling heat and plugs into wall power. Keep a few simple safety rules in place on your kitchen bench.
- Watch for steam burns: Starship Children's Health (Safekids) warns that hot steam and boiling water can scald skin in seconds. Keep babies and toddlers out of the kitchen when opening a hot unit.
- Push it back from the edge: place the machine near the back of the counter. Tuck the power cord behind it so little hands cannot pull the hot unit down.
- Give it headroom: do not run a steam steriliser directly under low wooden cupboards or power points. Rising steam can warp wood, peel paint or dampen outlets.
- Check the cord and plug: never use the machine if the cord is frayed, the plug is loose, or water has leaked inside the base.
- Unplug when not in use: if your unit does not have a timed clean-storage mode, switch it off at the wall once the cycle ends.
Troubleshooting common problems
If your machine starts acting up, try these simple checks before buying a new one.
- Bottles are still wet after drying: check that bottles are placed upside down, not upright. Check and clean the air filter on the bottom. Make sure you did not pour too much water onto the heating plate.
- The cycle stops too early: the plate likely has thick mineral scale, or you added too little water. Let it cool, descale the plate, and measure water carefully next time.
- A burning or sour smell: unplug and inspect the heating plate. Milk drips or burnt dust on the plate cause this smell. Let it cool, wipe with warm soapy water, then descale and rinse well.
- White dust on clean bottles: that is dried mineral scale from hard tap water. Descale the unit and try filtered or distilled water on the plate.
Frequently asked questions
Do I need to wash bottles before putting them in a steriliser?
Yes, every single time. A bottle steriliser kills germs, but it does not wash away milk fat or protein. If milk stays on the bottle, steam bakes it into a sticky film that protects germs from the heat. Always scrub bottles, rings and teats in warm soapy water and rinse well first.
How long do bottles stay sterile inside the machine?
Check your manual, because models vary. In general, if you keep the lid closed after the cycle ends, items stay sterile for up to 24 hours. Many dryers also run short bursts of warm, filtered air every hour or two to keep the inside dry. Once you open the lid, air and dust get in, so use the bottles soon or put them together with clean hands.
Can I use tap water in my bottle steriliser?
Yes, tap water is fine for steam sterilisers. The boiling step turns water into steam and leaves minerals behind. If your tap water is hard, white scale will build up faster on the heating plate. Using filtered or distilled water cuts down on scale and saves you cleaning time.
Why is my bottle dryer leaving water drops on the bottles?
Three common things cause wet bottles. First, the air filter on the bottom of the base may be clogged with dust. Second, bottles may be packed too tightly or standing upright, trapping water inside. Third, you may have poured too much water onto the plate at the start, leaving extra water to dry off.
How often should I descale my bottle steriliser?
Plan to descale every 1 to 2 weeks if you use hard tap water, or once a month with soft or filtered water. Do not wait until the machine stops working. As soon as you spot chalky white rings or brown spots on the metal plate, unplug it, let it cool, and soak the plate with white vinegar or citric acid.
Until what age do I need to sterilise baby bottles?
Advice depends on where you live. In Australia (Raising Children Network) and the UK (NHS), health bodies advise sterilising bottles and teats for the first 12 months. In the US (CDC) and Canada (Health Canada and Canadian Paediatric Society), daily sterilising is stressed most for newborns, babies under 2 to 4 months, premature babies, and babies with weak immune systems. Ask your child health nurse or doctor if you are unsure.
Sources
- NHS – Sterilising baby bottles
- CDC – Infant formula preparation and storage
- Raising Children Network – Baby formula: how to make and store it
- Pregnancy, Birth and Baby – Feeding your baby with formula
- Caring for Kids (Canadian Paediatric Society) – Feeding your baby in the first year
- World Health Organization – Safe preparation, storage and handling of powdered infant formula
- Food Standards Australia New Zealand – Bisphenol A (BPA)
- Starship Children's Health (New Zealand) – Burns and scalds
Pramod Rimal
Founder & editor
Practical, evidence-led guides for Australian families. We check claims against Australian standards and official health and safety guidance, and link our sources so you can check them too.
Visit Pramod Rimal’s website →About us and how we research →
Related guides
More Feeding & Baby Food →Ultrasonic Cleaners vs UV Steriliser Boxes: What Really Cleans Dummies and Baby Bottle Parts
9 Nov 2026 · 15 min read
How to Choose a Safe, Easy-to-Clean High Chair for Your Baby
7 Oct 2026 · 14 min read
How to Store and Organise Your Baby’s Meals Safely
30 Oct 2026 · 13 min read













