Dishwasher Baskets for Bottle Teats, Valves and Dummies: A Parent's Guide
How to use a dishwasher basket for bottle teats, pump valves and dummies so small silicone parts stay clean and away from hot coils.
PBy Pramod RimalPublished Updated 15 min read

On this page
- Key points
- What a dishwasher basket is and why you need one
- Why small silicone parts melt, warp, or get damaged
- Types of dishwasher baskets compared
- How to choose a safe dishwasher basket
- What can and cannot go in a dishwasher basket
- Step-by-step: how to load and run the dishwasher safely
- Dishwashing vs sterilising: what health bodies say
- Keeping silicone clean, odour-free and safe
- Common mistakes parents make
- Frequently asked questions
- Sources
Short answer: A dishwasher basket is a small cage that clips shut on the top rack of your dishwasher. It holds bottle teats (nipples), breast pump valves, and dummies (pacifiers) in one place. Without a basket, strong water jets can knock light silicone parts off the rack. They fall to the bottom, where a hot heating coil can melt them or food scraps can dirty them.
Always put the basket on the top rack, never the bottom rack. Take every bottle and pump part apart before loading. Check that the basket holes are small enough to keep tiny valves inside. After washing, check whether your baby's age or health means you also need to sterilise the parts. Health bodies in Australia, the UK, the US, and Canada all stress clean gear and safe water temperatures.
Key points
- Top rack only: Heating coils and the hottest water sit at the bottom of most dishwashers.
- Clip it shut: Water jets are strong. A loose lid lets small parts fly out.
- Take parts apart: Pull teats out of collars and remove tiny pump membranes before washing.
- Check the material: Silicone and hard plastic usually cope well. Natural rubber (latex) breaks down in heat.
- Watch the soap: Strong, scented pods leave a soapy taste on soft silicone.
- Know when to sterilise: A dishwasher cleans well, but young or sick babies often need an extra sterilising step.
What a dishwasher basket is and why you need one
Washing baby gear by hand takes time. A newborn can go through many bottles, pump sets, and dummies every day. A dishwasher saves you time and effort. Still, a normal dishwasher rack is built for plates and mugs, not tiny baby parts.
A baby gear dishwasher basket solves that problem. It is a small box or cage with a hinged lid and lots of holes. Water and soap spray through the holes to wash the items inside. Then the dirty water drains right back out.
People use different words for the same baby parts around the world. In Australia and the UK, parents say "teat" and "dummy". In the US and Canada, parents say "nipple" and "pacifier" or "soother". A dishwasher basket holds all of them, along with bottle collars, travel caps, sippy cup straws, and breast pump valves.
Without a basket, small parts move around during the wash. A lightweight silicone teat weighs almost nothing. One strong burst of water can flip it over or blow it straight through the rack bars. Once it falls to the bottom of the machine, three things can go wrong:
- It can land on the exposed heating coil and melt.
- It can jam the bottom spray arm or block the drain filter.
- It can sit in greasy food scraps at the bottom of the tub.
Why small silicone parts melt, warp, or get damaged
Many dishwashers have a metal heating element at the bottom of the tub. At the end of a wash, this coil gets very hot to dry the dishes. Some newer dishwashers hide the heater under the floor instead. Even then, the bottom of the tub gets much hotter than the top rack.
Food-grade silicone handles heat better than cheap plastic, so it does not melt as easily. However, if a silicone teat sits right on a glowing coil, it can still scorch, blister, or smell burnt. Plastic bottle collars, travel caps, and dummy shields warp even faster. A warped collar will not screw onto a bottle tightly, which causes leaks during a feed.
Heat is not the only risk. Water jets inside a dishwasher push hard. If a silicone teat is wedged onto a spike without a cover, it can flip upside down. Then it fills with soapy, dirty water like a little cup. At the end of the cycle, you pull out a teat full of grey water.
Harsh heat and strong detergent also wear out soft parts over time. Teats can turn cloudy, sticky, or stiff. Tiny tears can form around the hole at the tip. A damaged teat or dummy is not safe, because a piece could break off in your baby's mouth.
Types of dishwasher baskets compared
Not all dishwasher baskets work the same way. Some are simple cages, while others have special pegs and trays. Picking the right style depends on what you wash most often.
| Basket type | Best for | Water flow | Holds straws upright? | Risk of parts flipping |
|---|---|---|---|---|
| Single open cage | Dummies, bottle caps, big teats | High, open mesh | No | Medium, if underfilled |
| Two-tier split basket | Teats, collars, valves, membranes | High on both levels | Sometimes, on pegs | Low, if dividers fit |
| Silicone mesh pouch | Very tiny valves, O-rings, clips | Medium, smaller holes | No | Low, soft sides hug parts |
| Rack with straw pegs | Sippy cup straws and bottle vents | High through centre | Yes, built-in clips | Very low |
Single open cage
This is a simple box with a snap-on lid. It gives you one big space. It works well for bulky items like bottle collars, travel discs, and dummies. The downside is that small parts can pile on top of each other. When two teats nest together, soapy water cannot reach the inside of the bottom teat.
Two-tier split basket
This is the most common style for bottle-feeding families. It has a deep bottom section for collars and caps, plus a shallow top tray for teats and pump valves. Some models include fold-down dividers or pegs. These keep teats separated so water sprays inside every one.
Silicone pouch or fine-mesh basket
Some baskets use a soft silicone frame with very fine mesh or tiny slots. These are great for tiny breast pump parts, like duckbill valves and small white membranes. Standard cages often have wide slots that let tiny membranes slip right out. A fine-mesh pouch traps them safely.
Baskets with straw and vent holders
If you use anti-colic bottles or toddler straw cups, long thin tubes are hard to wash. Some baskets have upright clips or hollow pegs that hold straws straight up. That lets water shoot through the tube instead of washing only the outside.
How to choose a safe dishwasher basket
A dishwasher basket touches items that go straight into your baby's mouth. Spend a minute checking the design before you buy one.
Check for safe, BPA-free materials
Look for a basket made from BPA-free plastic, such as polypropylene, or food-grade silicone. BPA stands for bisphenol A, a chemical once used to make hard, clear plastics. Food standards bodies in Australia, the UK, the US, and Canada monitor food-contact plastics closely. Many baby gear makers stopped using BPA in infant feeding items years ago. Still, always check the label on the basket itself. It should clearly say "top-rack dishwasher safe" and "BPA-free".
Test the latch and hinges
A weak latch is the biggest flaw in cheap baskets. During a wash, hot water makes plastic flex slightly. If the clasp pops open, your teats and valves spill out onto the bottom rack. Look for a firm snap-lock tab or a sliding lock that clicks clearly. Plastic living hinges (thin strips that bend instead of metal pins) can also crack after months of heat, so inspect them now and then.
Look at the hole size
The holes must do two jobs at once. They need to be wide enough for strong water sprays to wash away milk fat. At the same time, they must be narrow enough to hold your smallest part. If you express breastmilk, hold a pump membrane up to the basket slots before buying. If the membrane can slide through the slot, choose a basket with a smaller grid.
Check the height against your dishwasher
Measure the space between your top dishwasher rack and the ceiling of the machine. Some dishwashers have a third thin cutlery tray right at the top. A tall two-tier basket might hit that tray or block the top spray arm. If your top rack is shallow, pick a slim, flat basket instead of a tall box.
Look for easy-to-clean corners
The basket itself needs to stay clean. Avoid designs with deep, narrow grooves where grease and old soap can hide. Smooth plastic and rounded corners rinse clean easily.
What can and cannot go in a dishwasher basket
Even with a great basket, not every baby item belongs in a dishwasher. Always read the care label from the maker of your bottle, pump, or dummy first.
| Usually safe in a top-rack basket | Wash by hand instead |
|---|---|
| Silicone bottle teats (check maker's guide) | Natural rubber or latex teats and dummies |
| Plastic bottle screw rings and travel caps | Breast pump air tubing (traps water inside) |
| Hard plastic breast pump flanges and shields | Wooden or fabric dummy clips and chains |
| Silicone duckbill valves and membranes (in fine mesh) | Soft, hollow dummies that trap water inside the bulb |
| One-piece silicone dummies (check maker's guide) | Any part with batteries, sensors, or electronics |
| Sippy cup valves and silicone straws | Items marked "hand wash only" |
Why natural rubber and latex stay out
Some parents prefer natural rubber (latex) teats and dummies. Natural rubber is soft, but it does not like high heat or dishwasher soap. A few hot washes can make latex swell, turn sticky, or crack. Wash natural rubber by hand in warm soapy water instead.
Why pump tubing stays out
Most electric breast pumps have thin plastic air tubes. Milk should not enter these tubes in a closed-system pump, and water should not enter them either. If you put tubing in a dishwasher, water gets stuck inside the long narrow pipe. It takes forever to dry and can grow mould. Keep tubes dry, or follow your pump manual if they ever need cleaning.
Watch out for water inside dummies
Some dummies have a hollow teat attached to a plastic shield. During a dishwasher cycle, water can force its way inside the hollow bulb. Dirty water trapped inside a dummy can breed germs. If you wash dummies in a basket, squeeze the bulb after the cycle. If water comes out, throw the dummy away or stick to one-piece silicone dummies that do not trap liquid.
Step-by-step: how to load and run the dishwasher safely
Good loading makes all the difference. Follow these steps to get clean parts without melting or soap taste.
- Rinse right after use. Run cold water over teats, valves, and collars as soon as your baby finishes feeding. Hot water can cook milk proteins onto silicone and leave a cloudy film.
- Take everything apart. Never leave a teat inside its screw collar. Milk hides in the narrow groove between the silicone and the plastic ring. Pull out anti-colic vents, pump membranes, and cup valves completely.
- Place parts face down. Put bottle teats and hollow caps pointing down on pegs or dividers. This stops water from pooling inside them. Leave a small gap between items so water hits every surface.
- Do not overfill the basket. If you jam ten teats into a small box, the middle ones stay dirty. Leave room for water to move freely.
- Snap the lid shut. Press the latches until they click. Give the lid a gentle tug to be sure it will not pop open.
- Load on the top rack only. Set the basket flat on the top rack. Spin the top spray arm with your hand before closing the door. Make sure the basket does not hit the arm.
- Choose mild, unscented detergent. Strong lemon or pine dishwasher pods cling to silicone. Your baby may refuse a bottle that tastes like soap. Pick a plain, fragrance-free powder or tablet. Avoid putting strongly spiced or tomato-rich dishes in the same load, as food smells also stick to silicone.
- Run the right cycle. Use a normal or hot wash cycle that your bottle maker approves. Skip extra high-heat drying boosts if your machine gets very hot, or let parts air-dry instead.
- Dry on a clean rack. Take the basket out as soon as the cycle ends. Shake off extra water and stand parts on a clean drying rack over a clean paper towel or cloth. Let them dry fully before putting them in a closed container.
Dishwashing vs sterilising: what health bodies say
Many parents wonder if a dishwasher is enough on its own. Washing and sterilising are two different steps. Washing removes milk, fat, and most germs. Sterilising kills almost all remaining germs.
Guidance varies a little by country and by your baby's age. All four countries agree that clean hands and thorough washing come first. They also agree that babies under 2 to 3 months, babies born early, and babies with weak immune systems need extra care.
| Country | Main health bodies | Dishwasher & cleaning advice | Sterilising advice |
|---|---|---|---|
| Australia | NHMRC, Raising Children Network, FSANZ | Wash bottles and teats in hot soapy water or a dishwasher. Rinse well before sterilising. | Sterilise all bottle-feeding gear until your baby is 12 months old. |
| UK | NHS, Office for Product Safety and Standards (OPSS) | Dishwashers clean bottles well, but do not sterilise them. Wash before sterilising. | Sterilise all feeding equipment until your baby is at least 12 months old. |
| US | CDC, FDA, American Academy of Pediatrics (AAP), CPSC | Dishwasher with hot water and a heated drying or sanitising cycle can sanitise items. | Sanitise daily if baby is under 2 months, born early, or has a weak immune system. |
| Canada | Health Canada, Canadian Paediatric Society (CPS) | Wash in hot soapy water or dishwasher; rinse well. | Sterilise for young infants, especially in the first months, or follow local public health rules. |
Look closely at the difference between regions. In Australia, the NHMRC and Raising Children Network tell parents to sterilise bottle-feeding equipment until 12 months of age. The NHS in the UK gives the same 12-month rule, and states clearly that a dishwasher cleans bottles but does not sterilise them.
In the US, the CDC says a dishwasher with hot water and a heated drying cycle (or sanitising setting) can help sanitise feeding items. Even there, the CDC advises extra daily sanitising for babies under 2 months old, premature babies, or babies with health problems. In Canada, the Canadian Paediatric Society and Health Canada stress careful washing and boiling or sterilising for newborn feeding gear.
What about breast pump parts? If your baby is healthy and full-term, health bodies often say washing pump parts thoroughly in hot soapy water or a dishwasher after each use is enough. If your baby is under 2 to 3 months, born early, or unwell, sanitising or sterilising pump parts once a day is safer. Always check with your doctor, midwife, or child health nurse if you are unsure.
A note on hot water and plastic bottles
Research has looked at how very hot water affects plastic baby bottles made from polypropylene. Heating plastic to very high temperatures can release tiny plastic particles into liquid. Silicone and glass do not shed plastic particles in the same way. If you use plastic parts, avoid scrubbing them with rough brushes that scratch the surface, and replace worn or cloudy plastic gear promptly.
Keeping silicone clean, odour-free and safe
Silicone is soft, flexible, and easy to shape into bottle teats and pump valves. Those same traits make it act a bit like a sponge for smells and oils.
Stopping soap and food smells
If your baby suddenly pulls away from a bottle, smell the teat. Silicone picks up scents from scented dishwasher tablets, rinse aids, and greasy dinner plates. Tomato sauce, curry, garlic, and onion oils cling to silicone fast.
The easiest fix is to wash baby gear in a separate load, or with plain items like water glasses and clean plates. Use a fragrance-free dishwasher detergent. Skip scented rinse aids when washing baby gear if you notice a film or smell.
Removing cloudy milk residue
Sometimes silicone turns milky white. This is often from milk fat or hard water minerals in your tap water. Never use bleach, harsh chemicals, or steel wool to scrub teats. Instead, soak the clean silicone parts in warm water with a splash of plain white vinegar for a short time, then rinse well in clean water and wash again with mild soap.
Checking for wear and tear
Dishwashers expose baby parts to heat and water jets day after day. Check every teat, valve, and dummy before you use it:
- Do the pull test: Tug gently on the bulb of a teat or dummy in all directions. If it feels thin, sticky, or starts to tear, throw it out.
- Check the tip hole: If a bottle teat hole stretches out, milk flows too fast and can make your baby cough or gag.
- Inspect pump valves: A tiny nick in a silicone duckbill valve stops suction from working. Your pump will feel weak even if the motor is fine.
- Check for bite marks: Once your baby gets teeth, they can chew through silicone. Throw away chewed teats and dummies right away to prevent choking.
Common mistakes parents make
Even careful parents run into trouble with dishwasher baskets. Here are the six most common slip-ups and how to avoid them.
- Putting the basket on the bottom rack. Space gets tight on the top rack, so it is tempting to drop the basket onto the bottom rack. Do not do it. That puts thin silicone and plastic collars inches from the heating coil and in the path of heavy food debris.
- Leaving teats inside screw rings. It feels faster to toss the assembled collar and teat into the basket together. Milk fat stays trapped in the ridge between them. Always pull the teat out first.
- Packing the basket too tight. When parts press against each other, water cannot rinse away milk or soap. Give each item room to breathe.
- Using scented pods or strong rinse aid. Babies have a sharp sense of smell and taste. A teat that smells like lemon soap can put a baby off feeding.
- Forgetting the dishwasher filter. Almost every dishwasher has a mesh filter at the bottom of the tub. If you never clean it, old food grease washes back up onto your baby's teats. Rinse the filter under the tap once a week.
- Skipping safety checks on the basket itself. Over time, the basket's hinges can crack or warp. If the lid does not lock tight, replace the basket before it spills parts onto the heating element.
Frequently asked questions
Can I put a dishwasher basket on the bottom rack if the top rack is full?
No. Keep the dishwasher basket on the top rack every time. The bottom rack sits closest to the heating coil, which can melt plastic collars and scorch silicone teats. The bottom rack also catches more grease and food scraps from pots and plates.
Do I still need to sterilise bottle teats after using the dishwasher?
Often, yes, depending on where you live and your baby's age. In Australia and the UK, health bodies advise sterilising all bottle-feeding gear until your baby turns 12 months old, even after dishwashing. In the US and Canada, a hot dishwasher with a sanitising or heated dry cycle can sanitise gear for older healthy babies, while newborns, premature babies, and sick babies still need daily sterilising. Check your local health guidelines.
Why do my baby's silicone teats smell like soap after the dishwasher?
Silicone absorbs scents easily from fragranced dishwasher pods, rinse aids, and strong-smelling foods. Switch to a plain, unscented dishwasher detergent and wash baby parts separately from greasy or spicy dinner dishes. If the smell stays, soak the clean teats in warm water with a little baking soda or white vinegar, then rinse well.
Can I wash breast pump valves and membranes in a dishwasher basket?
Check your pump manual first. Many hard plastic flanges and silicone valves are top-rack dishwasher safe, as long as your basket has small enough holes so tiny membranes cannot slip out. However, dishwashers and high heat can wear out soft duckbill valves faster than gentle hand washing. Never put breast pump air tubing in the dishwasher.
Can dummies (pacifiers) go in a dishwasher basket?
Many one-piece silicone dummies are top-rack dishwasher safe, but always check the maker's label. Keep natural rubber (latex) dummies out of the dishwasher, because heat makes rubber break down and turn sticky. Also avoid dishwashing hollow dummies that let water leak inside the bulb, as trapped water can grow mould or bacteria.
How often should I clean the dishwasher basket itself?
Since the basket sits in hot soapy water during every cycle, it stays fairly clean on its own. Still, give it a quick look once a week. Scrub any slimy spots or soap build-up in the corners and latches with a clean bottle brush, and check that the clasps still snap shut firmly.
Sources
- Raising Children Network – Baby formula: how to make and store it
- NHMRC – Infant Feeding Guidelines
- Food Standards Australia New Zealand – Bisphenol A (BPA)
- NHS – Sterilising baby bottles
- CDC – Infant formula preparation and storage
- U.S. FDA – Bisphenol A (BPA): use in food contact application
- Caring for Kids, Canadian Paediatric Society – Feeding your baby in the first year
Pramod Rimal
Founder & editor
Practical, evidence-led guides for Australian families. We check claims against Australian standards and official health and safety guidance, and link our sources so you can check them too.
Visit Pramod Rimal’s website →About us and how we research →
Related guides
More Feeding & Baby Food →Ultrasonic Cleaners vs UV Steriliser Boxes: What Really Cleans Dummies and Baby Bottle Parts
9 Nov 2026 · 15 min read
Countertop Bottle Drying Racks vs Vertical Drying Trees: Airflow, Drainage, and Stopping Slimy Buildup
9 Nov 2026 · 15 min read
All-in-One Bottle Washers vs. Steam Sterilisers: Which Machine Suits Your Home?
16 Nov 2026 · 15 min read













